Disponible en 7 couleurs de plastique de base et en 6 couleurs métalliques (voir variantes du produit)         Les stabilisateurs d’écrous sont composés de plastique de fibre de verre et ont les mêmes propriétés matérielles que le support. De plus, ils disposent d’un grand nombre de pièces de vissage spéciales en métal léger, dont les grandes surfaces de pression permettent une fixation par coulissement ménageant le plastique, parfaite et sans jeu. Le stabilisateur d’écrou est équipé d’écrous de blocage qui sont ancrés dans le plastique en toute sécurité grâce à des pattes de blocage. Le stabilisateur à vis est équipé du nombre adéquat d’écrous spéciaux qui sont protégés de la casse par une rondelle de blocage et garantissent un haut niveau de stabilité et de sécurité avec un couple de serrage de 1,2 Nm maximum. Avantages :  Changement rapide de la lame  ++  Raccordement solide entre la lame et le support  ++  Renforcement de l'axe transversal et longitudinal des patins grâce à la vis de stabilisation  ++  Raccords à vis en métal léger protégés par unbouchon en plastique de grande surface  ++  Pièces de vissage à l’épreuve des dysfonctionnements  ++  Des lames / supports parfaitement ajustés Positionnement au moyen de contre-écrous coniques  ++  Apparence extravagante Des options de visuels de conception extravagants grâce à une large gamme de couleurs.  ++   Illustrations à titre d’exemple - le stabilisateur avec une longueur de système de 248 mm a 4 montants et 5 trous de boulons, à partir de la longueur de système de 256 mm il dispose de 5 montants et 6 trous de boulons.  

Stabilisator grün lackiert, Einzelstücke nur in der Länge 256 Die Stabilisatoren:             Erhältlich in  7  Kunststoff Grundfarben sowie in                                                 6  Metallic-Farben  (siehe Produkt-Varianten)         Die Verschraubungsstabilisatoren bestehen aus Glasfaser-Kunststoff und besitzen die identischen Materialeigenschaften des Holder. Darüber hinaus verfügen sie über eine Vielzahl von speziellen Leichtmetall Verschraubungsteilen, deren große Pressflächen eine Kunststoffschonende, perfekte und spielfreie Runner Befestigung ermöglichen. Der Muttern-Stabilisator ist mit Rastmuttern bestückt, die über Rastnasen ausfallsicher im Kunststoff verankert sind. Passend dazu ist der Schrauben-Stabilisator mit der deckungsgleichen Anzahl von speziellen Schrauben ausgestattet die mittels einer Sicherungsscheibe gegen Ausfallen abgesichert sind und bei einem Anzugsdrehmoment von max. 1,2 Nm ein hohes Maß an Stabilität und Sicherheit gewährleisten. Vorteile:  Schneller Runner-Wechsel  ++  Stabile Schraubverbindung von Runner und Holder  ++  Versteifung der Kufen Quer- und Längsachse über die Stabilisatoren-Verschraubung  ++  Großflächige, Kunststopf-Schonende Leichtmetall-Verschraubungen  ++  Ausfallgesicherte Verschraubungsteile  ++  Perfekte, formschlüssige Runner / Holder Positionierung über Konus-Rastmuttern  ++  Extravagante optische Gestaltungsmöglichkeit durch vielfältiges Farbangebot  ++   Abbildungen beispielhaft - der Stabilisator mit Systemlänge 248 mm hat 4 Rungen und 5 Schraubenlöcher, ab Systemlänge 256 mm sind es 5 Rungen und 6 Schraubenlöcher.   English CharacteristicsThe stabilizer is made of glass fiber plastic and serves to fix the runner. It consists of a screw and nut side, which are connected bymeans of a system key. The stabilizer is available in seven standard colors and 6 further metallic variants. Advantages-Quick & easy runner exchange -Fail-proof screwing parts -Stable connection between holder  & runner -Various design optionsHandlingLoosen all the screws of the stabilizer by means of the system key. Then, press with the key against the screws for detaching the nutside of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After having exchanged the runner, push the nut sideinto the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and  dismounting, the screw side of the stabilizer should always be on the inner shoe side. 

The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants. Advantages  Quick & Easy Runner Exchange Fail-proof screwing parts Stable connection between holder & runner Use Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side. 

The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants. Advantages  Quick & Easy Runner Exchange Fail-proof screwing parts Stable connection between holder & runner Use Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side. 

The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants. Advantages  Quick & Easy Runner Exchange Fail-proof screwing parts Stable connection between holder & runner Use Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side. 

The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants. Advantages  Quick & Easy Runner Exchange Fail-proof screwing parts Stable connection between holder & runner Use Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side. 

The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants. Advantages  Quick & Easy Runner Exchange Fail-proof screwing parts Stable connection between holder & runner Use Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side. 

The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants. Advantages  Quick & Easy Runner Exchange Fail-proof screwing parts Stable connection between holder & runner Use Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side. 

The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants. Advantages  Quick & Easy Runner Exchange Fail-proof screwing parts Stable connection between holder & runner Use Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side. 

The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants. Advantages  Quick & Easy Runner Exchange Fail-proof screwing parts Stable connection between holder & runner Use Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side. 

The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants. Advantages  Quick & Easy Runner Exchange Fail-proof screwing parts Stable connection between holder & runner Use Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side. 

The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants. Advantages  Quick & Easy Runner Exchange Fail-proof screwing parts Stable connection between holder & runner Use Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side. 

The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants. Advantages  Quick & Easy Runner Exchange Fail-proof screwing parts Stable connection between holder & runner Use Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side. 

The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants. Advantages  Quick & Easy Runner Exchange Fail-proof screwing parts Stable connection between holder & runner Use Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side. 

The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants. Advantages  Quick & Easy Runner Exchange Fail-proof screwing parts Stable connection between holder & runner Use Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side. 

The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants. Advantages  Quick & Easy Runner Exchange Fail-proof screwing parts Stable connection between holder & runner Use Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side.