Disponible en 7 couleurs de plastique de base et en 6 couleurs métalliques (voir variantes du produit) Les stabilisateurs d’écrous sont composés de plastique de fibre de verre et ont les mêmes propriétés matérielles que le support. De plus, ils disposent d’un grand nombre de pièces de vissage spéciales en métal léger, dont les grandes surfaces de pression permettent une fixation par coulissement ménageant le plastique, parfaite et sans jeu. Le stabilisateur d’écrou est équipé d’écrous de blocage qui sont ancrés dans le plastique en toute sécurité grâce à des pattes de blocage. Le stabilisateur à vis est équipé du nombre adéquat d’écrous spéciaux qui sont protégés de la casse par une rondelle de blocage et garantissent un haut niveau de stabilité et de sécurité avec un couple de serrage de 1,2 Nm maximum.
Avantages :
Changement rapide de la lame ++ Raccordement solide entre la lame et le support ++ Renforcement de l'axe transversal et longitudinal des patins grâce à la vis de stabilisation ++ Raccords à vis en métal léger protégés par unbouchon en plastique de grande surface ++ Pièces de vissage à l’épreuve des dysfonctionnements ++ Des lames / supports parfaitement ajustés Positionnement au moyen de contre-écrous coniques ++ Apparence extravagante Des options de visuels de conception extravagants grâce à une large gamme de couleurs. ++
Illustrations à titre d’exemple - le stabilisateur avec une longueur de système de 248 mm a 4 montants et 5 trous de boulons, à partir de la longueur de système de 256 mm il dispose de 5 montants et 6 trous de boulons.
The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants.
Advantages
Quick & Easy Runner Exchange
Fail-proof screwing parts
Stable connection between holder & runner
Use
Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side.
Der Logo Clip: Erhältlich in 3 Standard-Kunststofffarben sowie 6 Metallic-Farben (siehe Produkt-Varianten)Der Logo Clip thematisiert mit seiner Ausgestaltung den Markennamen t-blade (Thermo- Messer) und verweist in seinem Logo auf die exzellenten thermischen Eigenschaften des Kufensystems.
Das zentrale Emblem t zeigt den Anfangsbuchstaben des weltweit geschützten Markennamen t-blade sowie eine lodernde Flamme, die symbolisch auf die Erzeugung einer überdurchschnittlich hohen Gleitflächen Temperatur hinweist.
Das bestechend Logo besteht aus Kunststoff und rastet passgenau in die Konturform am Holder-Heck ein. Durch seitliches einschieben eines kleinen Schraubendrehers in die Flamme, lässt sich der Logo-Clip aus der Verrastung aushebeln und kann problemlos ausgetauscht werden.
Über eine Vielzahl von Farben kann der Logo-Clip dem persönlichen Geschmack des System-Nutzers angepasst werden.Vorteile:Hoher Marken Erkennungswert ++ exzellente Produktoptik ++ Hochwertige Markenbezeichnung ++ individuelle Farbgestaltung ++ leichte Austauschbarkeit.
English
ClipCharacteristicsThe t'blade clip, which is attached to the holder, is available in colors which match with the one of the stabilizer. It is made of non-reinforced plastic and is available in 2 standard colors as well as 6 metallic variants. The logo clip has a pure design function.
The skate blade system consists of three parts, the holder, the stabilizers and the runner. All system components are made of a highly concentrated, especially reinforced glass fiber or carbon fiber plastic material providing good low temperature impact strength. Based on the excellent system stability, the t'blade runner can take user weight loads of a maximum of 120 kg (264 lbs.) and can be used for hockey games up to an outside temperature of approximately.-25 degrees without any problems.The complete system contains a pair of :
white holders
grey stabilizers
white runners (M 13)
red clips
The skate blade system: The development of the t’ blade blade system took place as a result to create a blade system which is capable of eliminating a deficiency existing since than more 100 years in the sector of ice skate blades. With the market launch of the t’blade interchangeable runner technology, the market has for the first time in the history of ice skates a runner system which does not require a time-consuming and cost-intensive inaccurate sharpening process of the runner edges. The restoration of optimum gliding characteristics is achieved exclusively by the quick replacement of the t’blade interchangeable runners. The runner system has not only a wide range of outstanding features, but occupies a top position in the areas concerning gliding characteristics, maneuverability, high cornering speed, and braking deceleration. Furthermore, new standards have been set concerning the use of ice skate blades in areas like product stability, service life, system handling, product service and manufacturing quality. The interchangeable runners manufactured with the greatest precision have an absolutely constant rocker shape (contact area) and are only distinguished by the gliding surface length, the radius of hollow and the system size. A wide variety of versions allow the system user an accurate matching of the runner to suit the current state of the ice surface taking into account simultaneously its expectations concerning gliding characteristics during skating. The system matching is effected taking into account of the user weight and the ice surface temperature by modifying the gliding surface length and the radius of hollow. The skate blade system consists of three parts, the holder, the stabilizers and the runner. All system components are made of a highly concentrated, especially reinforced glass fiber or carbon fiber plastic material providing good low temperature impact strength. With a weight of < 189 grams, relative to the reference system size 272, the carbon runner is the lightest ice skate blade on the market . Based on the excellent system stability, the t'blade runner can take user weight loads of a maximum of 120 kg (264 lbs.) and can be used for hockey games up to an outside temperature of approximately -25 degrees C° without any problems. You can find a detailed description in the blade system area (runner) under "HOLDER, STABILIZERS and RUNNER".The holder:
available in 6 different colors
as well as in 6 metallized colors (refer to product variants)
The holder consists of high-strength impact-resistant fibrous plastic (glass or carbon fiber) which withstands temperatures of up to -25℃. Its ingenious bridge-like structure over the entire length from the front to the rear portion of the holder combined with the integrated cross ribs provide a high degree of rigidity with excellent torsional, longitudinal and transversal stability characteristics. The design related rigidity of the holder stabilizes the sole of the shoe in a sustainable manner and minimizes the axial bending forces in the central area of the ice skate shoe. A trapezoid shaped connecting element between the runner and the holder ensures a precise and tight seating of the runner into the holder enabling the transfer of acceleration and transverse cornering forces. To ensure a proper installation of the stabilizers, the inner side of the holder is provided with little cavities which are intended to install the locking washers of the screws to hold the stabilizers in place. If required, the holes around the perimeter of the sole can be used for securing the holder onto the sole of the ice skate. The fastening can then be realized by means of rivets or RMS screws.A recess located at the rear of the holder is provided for inserting the t’blade logo clip. Proper function and maximum rigidity of the holder are only ensured if all components are assembled. Advantages:
extreme stability of the holder thanks to the triangle of forces
maximum longitudinal and transversal stability characteristics
closed structure between the front and the rear area
visual differentiation thanks to the recesses and the bridge-like structure
sustained improvement of the rigidity of the sole of the ice skate shoe
The stabilizers:
available in 6 different colors
as well as in 6 metallized colors (refer to product variants)
The stabilizers are made of glass fiber plastic and have identical material properties as the holder. In addition, they are provided with a set of special light alloy screws and sockets to ensure play-free securing of the runner without damaging the plastic. There are two stabilizers on each t-blade system, one holding the nuts which are press-fitted to prevent them from falling out. The other one with the same number of special screws and locking washers to prevent them from being lost coincides perfectly with the nuts of the female stabilizer. The tightening torque of 1,2 Nm ensures a high level of stability and safety.Advantages:
rapid exchange of the runner
stable assembly of runner and holder
stiffening of transverse and longitudinal axis of the runner by means of the stabilizers
special light alloy screws and sockets to avoid damaging the plastic
special locking washers secured against losing
perfect form-closed positioning of the runner and the holder using cone clamping elements
extravagant design possibilities with a wide range of colors
The runner:
available per system size in 18 rocker shape variants
as well as in 2 different colors white and black
Detailed description of the available runner versions refer to product variants. The runner is an innovative very complex and technologically sophisticated composite product which constitutes almost the entire key technology of the t’blade runner system.The fabrication of the high-precision 1 mm thick metal band requires the use of the ultra-modern laser technology by means of complex production lines meeting the closest tolerances. The fracture resistant profiled running strip is made of a stainless steel or metal alloy which is injected into a low temperature resistant glass fiber or carbon fiber plastic .The highly compressed profiled running strip is manufactured by rolling and has an enormous edge hardness of approx. 55 HRC = 570 HV after an expensive and time-consuming fabrication process. The available maximum hardness achieves a useful life 4 times longer than traditional steel blades. Due to the very small metal mass (approx. 5.5g) of the running strip and a minimum plastic mass (approx. 45g), the t-blade composite runner is the lightest ice skate blade on the market worldwide. Due to the very small size of the profiled running strip, the runner has exceptional thermal properties which in conjunction with the highly polished running surface of the runner lead to an above-average improvement of the gliding characteristics up to 40 %. Due to its absolutely constant rocker shape, the runner available in many types allows a quick and perfect restoration of the usual optimum gliding characteristics. As soon as the running edges are worn or damaged, a rapid and simple replacement of the runner is required. Thus a time-consuming and cost-intensive inaccurate sharpening process of the runner edges is avoided. The rocker shape available in many versions is determined by three crucial factors: Gliding surface length, radius of hollow and system size (refer to product variants and rocker shape matching)Advantages:
extremely light
excellent gliding characteristics
good maneuverability
high cornering speed
small curve radii
fracture resistant
constant rocker shape geometry
running edges sharpening not required
above-average hardness of the running edges
useful life 4 times longer
rapid runner exchange
The logo clip:
available in 6 different colors
as well as in 6 metallized colors (refer to product variants)
The logo clip identifies the t’blade trademark (thermal blade) and refers to the outstanding thermal characteristics of the t'blade runner system.The central emblem shows the initial letter "t" which indicates the registered " t’blade brand name "as well as the blazing flame symbolizing the above-average temperature on the gliding surface. The impressively simple logo is made of not-reinforced plastic and fits exactly into the cavity intended for this purpose in the rear part of the holder. The logo clip can be replaced without any problem by inserting a screwdriver tip into the unlocking opening where the flame is located so that it can be dislodged easily. The logo-clip can be customized to suit the personal taste of the system user by means of a variety of colors. Advantages:
strong brand recognition
excellent visual appearance of the product
high-quality trademark
customized colors
easy interchangeability
The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants.
Advantages
Quick & Easy Runner Exchange
Fail-proof screwing parts
Stable connection between holder & runner
Use
Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side.
The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants.
Advantages
Quick & Easy Runner Exchange
Fail-proof screwing parts
Stable connection between holder & runner
Use
Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side.
The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants.
Advantages
Quick & Easy Runner Exchange
Fail-proof screwing parts
Stable connection between holder & runner
Use
Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side.
Der Logo Clip: Erhältlich in 3 Standard-Kunststofffarben sowie 6 Metallic-Farben (siehe Produkt-Varianten)Der Logo Clip thematisiert mit seiner Ausgestaltung den Markennamen t-blade (Thermo- Messer) und verweist in seinem Logo auf die exzellenten thermischen Eigenschaften des Kufensystems.
Das zentrale Emblem t zeigt den Anfangsbuchstaben des weltweit geschützten Markennamen t-blade sowie eine lodernde Flamme, die symbolisch auf die Erzeugung einer überdurchschnittlich hohen Gleitflächen Temperatur hinweist.
Das bestechend Logo besteht aus Kunststoff und rastet passgenau in die Konturform am Holder-Heck ein. Durch seitliches einschieben eines kleinen Schraubendrehers in die Flamme, lässt sich der Logo-Clip aus der Verrastung aushebeln und kann problemlos ausgetauscht werden.
Über eine Vielzahl von Farben kann der Logo-Clip dem persönlichen Geschmack des System-Nutzers angepasst werden.Vorteile:Hoher Marken Erkennungswert ++ exzellente Produktoptik ++ Hochwertige Markenbezeichnung ++ individuelle Farbgestaltung ++ leichte Austauschbarkeit.
English
ClipCharacteristicsThe t'blade clip, which is attached to the holder, is available in colors which match with the one of the stabilizer. It is made of non-reinforced plastic and is available in 2 standard colors as well as 6 metallic variants. The logo clip has a pure design function.
The skate blade system consists of three parts, the holder, the stabilizers and the runner. All system components are made of a highly concentrated, especially reinforced glass fiber or carbon fiber plastic material providing good low temperature impact strength. Based on the excellent system stability, the t'blade runner can take user weight loads of a maximum of 120 kg (264 lbs.) and can be used for hockey games up to an outside temperature of approximately.-25 degrees without any problems.The complete system contains a pair of :
white holders
grey stabilizers
white runners (M 13)
red clips
The skate blade system: The development of the t’ blade blade system took place as a result to create a blade system which is capable of eliminating a deficiency existing since than more 100 years in the sector of ice skate blades. With the market launch of the t’blade interchangeable runner technology, the market has for the first time in the history of ice skates a runner system which does not require a time-consuming and cost-intensive inaccurate sharpening process of the runner edges. The restoration of optimum gliding characteristics is achieved exclusively by the quick replacement of the t’blade interchangeable runners. The runner system has not only a wide range of outstanding features, but occupies a top position in the areas concerning gliding characteristics, maneuverability, high cornering speed, and braking deceleration. Furthermore, new standards have been set concerning the use of ice skate blades in areas like product stability, service life, system handling, product service and manufacturing quality. The interchangeable runners manufactured with the greatest precision have an absolutely constant rocker shape (contact area) and are only distinguished by the gliding surface length, the radius of hollow and the system size. A wide variety of versions allow the system user an accurate matching of the runner to suit the current state of the ice surface taking into account simultaneously its expectations concerning gliding characteristics during skating. The system matching is effected taking into account of the user weight and the ice surface temperature by modifying the gliding surface length and the radius of hollow. The skate blade system consists of three parts, the holder, the stabilizers and the runner. All system components are made of a highly concentrated, especially reinforced glass fiber or carbon fiber plastic material providing good low temperature impact strength. With a weight of < 189 grams, relative to the reference system size 272, the carbon runner is the lightest ice skate blade on the market . Based on the excellent system stability, the t'blade runner can take user weight loads of a maximum of 120 kg (264 lbs.) and can be used for hockey games up to an outside temperature of approximately -25 degrees C° without any problems. You can find a detailed description in the blade system area (runner) under "HOLDER, STABILIZERS and RUNNER".The holder:
available in 6 different colors
as well as in 6 metallized colors (refer to product variants)
The holder consists of high-strength impact-resistant fibrous plastic (glass or carbon fiber) which withstands temperatures of up to -25℃. Its ingenious bridge-like structure over the entire length from the front to the rear portion of the holder combined with the integrated cross ribs provide a high degree of rigidity with excellent torsional, longitudinal and transversal stability characteristics. The design related rigidity of the holder stabilizes the sole of the shoe in a sustainable manner and minimizes the axial bending forces in the central area of the ice skate shoe. A trapezoid shaped connecting element between the runner and the holder ensures a precise and tight seating of the runner into the holder enabling the transfer of acceleration and transverse cornering forces. To ensure a proper installation of the stabilizers, the inner side of the holder is provided with little cavities which are intended to install the locking washers of the screws to hold the stabilizers in place. If required, the holes around the perimeter of the sole can be used for securing the holder onto the sole of the ice skate. The fastening can then be realized by means of rivets or RMS screws.A recess located at the rear of the holder is provided for inserting the t’blade logo clip. Proper function and maximum rigidity of the holder are only ensured if all components are assembled. Advantages:
extreme stability of the holder thanks to the triangle of forces
maximum longitudinal and transversal stability characteristics
closed structure between the front and the rear area
visual differentiation thanks to the recesses and the bridge-like structure
sustained improvement of the rigidity of the sole of the ice skate shoe
The stabilizers:
available in 6 different colors
as well as in 6 metallized colors (refer to product variants)
The stabilizers are made of glass fiber plastic and have identical material properties as the holder. In addition, they are provided with a set of special light alloy screws and sockets to ensure play-free securing of the runner without damaging the plastic. There are two stabilizers on each t-blade system, one holding the nuts which are press-fitted to prevent them from falling out. The other one with the same number of special screws and locking washers to prevent them from being lost coincides perfectly with the nuts of the female stabilizer. The tightening torque of 1,2 Nm ensures a high level of stability and safety.Advantages:
rapid exchange of the runner
stable assembly of runner and holder
stiffening of transverse and longitudinal axis of the runner by means of the stabilizers
special light alloy screws and sockets to avoid damaging the plastic
special locking washers secured against losing
perfect form-closed positioning of the runner and the holder using cone clamping elements
extravagant design possibilities with a wide range of colors
The runner:
available per system size in 18 rocker shape variants
as well as in 2 different colors white and black
Detailed description of the available runner versions refer to product variants. The runner is an innovative very complex and technologically sophisticated composite product which constitutes almost the entire key technology of the t’blade runner system.The fabrication of the high-precision 1 mm thick metal band requires the use of the ultra-modern laser technology by means of complex production lines meeting the closest tolerances. The fracture resistant profiled running strip is made of a stainless steel or metal alloy which is injected into a low temperature resistant glass fiber or carbon fiber plastic .The highly compressed profiled running strip is manufactured by rolling and has an enormous edge hardness of approx. 55 HRC = 570 HV after an expensive and time-consuming fabrication process. The available maximum hardness achieves a useful life 4 times longer than traditional steel blades. Due to the very small metal mass (approx. 5.5g) of the running strip and a minimum plastic mass (approx. 45g), the t-blade composite runner is the lightest ice skate blade on the market worldwide. Due to the very small size of the profiled running strip, the runner has exceptional thermal properties which in conjunction with the highly polished running surface of the runner lead to an above-average improvement of the gliding characteristics up to 40 %. Due to its absolutely constant rocker shape, the runner available in many types allows a quick and perfect restoration of the usual optimum gliding characteristics. As soon as the running edges are worn or damaged, a rapid and simple replacement of the runner is required. Thus a time-consuming and cost-intensive inaccurate sharpening process of the runner edges is avoided. The rocker shape available in many versions is determined by three crucial factors: Gliding surface length, radius of hollow and system size (refer to product variants and rocker shape matching)Advantages:
extremely light
excellent gliding characteristics
good maneuverability
high cornering speed
small curve radii
fracture resistant
constant rocker shape geometry
running edges sharpening not required
above-average hardness of the running edges
useful life 4 times longer
rapid runner exchange
The logo clip:
available in 6 different colors
as well as in 6 metallized colors (refer to product variants)
The logo clip identifies the t’blade trademark (thermal blade) and refers to the outstanding thermal characteristics of the t'blade runner system.The central emblem shows the initial letter "t" which indicates the registered " t’blade brand name "as well as the blazing flame symbolizing the above-average temperature on the gliding surface. The impressively simple logo is made of not-reinforced plastic and fits exactly into the cavity intended for this purpose in the rear part of the holder. The logo clip can be replaced without any problem by inserting a screwdriver tip into the unlocking opening where the flame is located so that it can be dislodged easily. The logo-clip can be customized to suit the personal taste of the system user by means of a variety of colors. Advantages:
strong brand recognition
excellent visual appearance of the product
high-quality trademark
customized colors
easy interchangeability
Der Holder besteht aus einem kälteschlagzähen Kunststoff der bis zu einer Temperatur von maximal - 25 ° Celsius splitterbruchsicher ist. Seine effiziente brückenartige Konstruktion erstreckt sich durchgängige von der Holderfront bis zum Holderheck und führt im Verbund mit den integrierten Querrippen zu einem extrem steifen Holder mit hervorragenden Torsion, Längs- und Querstabilitätseigenschaften. Die konstruktionsbedingte Steifigkeit des Holders stabilisiert die Schlittschuhsohle nachhaltig und minimiert die axialen Biegekräfte im Zentralbereich des Schlittschuhstiefels. Mit einer genau definierten und geschlossenen Holder Sprengung unterstützt die Holderkonstruktion nachhaltig den optimalen Kniepunkt Vorhaltewinkel des Kufensystem Nutzers. Eine trapezartige Verbindung zwischen Runner und Holder gewährleistet einen spielfreien und passgenauen Sitz des Runners im Holder und ermöglicht dadurch die Übertragung von großen Beschleunigungs- und Kurvenquerkräften. Um eine planflächige und stabile Verbauung der Stabilisatoren zu ermöglichen, befinden sich an den Verschraubungspunkten im Bereich der Holder Innenseite, kleine Mulden, die dazu geeignet sind, die Sicherungsscheiben des Schrauben Stabilisators aufzunehmen. Eine fehlerhafte Montage der Stabilisatoren führt zwangsweise zu einem Stabilitätsverlust der Runner Verschraubung und beschleunigt die Zerstörung der Kunststoff Sicherungsscheiben. Die im Holder Sohlenrand umlaufend eingebrachten Befestigungslöcher können je nach Bedarf und Position zum befestigen des Holders an der Schlittschuhstiefelsohle benutzt werden. Die Befestigung kann mittels Nieten oder RMS Verschraubung erfolgen.Im Heckbereich des Holder befindet sich die Konturöffnung für das Einklinkbahre t-blade Logo-Clip Markenzeichen
Der Holder erreicht seine maximale Steifigkeit und Betriebssicherheit erst im Verbund aller Systemteile. Vorteile:Extreme Holder Stabilität durch Kräftedreieck-Konstruktion ++
Maximale Quer- und Längskraftstabilität ++ Geschlossene Holder
Konstruktion zwischen Front- und Heckbereich ++ Optische
Differenzierung durch Mehrloch- und Brückendesign ++ Nachhaltige
Verbesserung der Schlittschuhsohlensteifigkeit ++
Abbildungen beispielhaft - der Holder mit Systemlänge 248 mm hat 4 Aussparungen, ab Systemlänge 256 mm sind es 5 Aussparungen.
___________________________________________________________________
English
The holder forms the blade holder of the t'blade system and it is available in 2 standard colors (glass fiber plastic) as well as a carbon variant (carbon fiber plastic). The bridge-type construction, combined with the integrated lateral ribs, leads to an extremely stiff holder with good torsion, lateral and vertical stability characteristics. By means of the holes which are provided at the sole border, the holder can be fitted to the shoe via rivets or an RMS connection. Advantages-Holder made of fiber reinforced plastic -Cold impact resistant and chip fracture safe up to -25° C -Closed construction between front and heel area -Extreme stability by means of the triangle of forces construction - Improves stiffness of skate outsole-Maximum shear and longitudinal force stability System sizesStandard system: 248, 256, 264, 272, 280, 288, 300mm Carbon system: 248, 256, 264, 272, 280, 288, 300mm
The skate blade system consists of three parts, the holder, the stabilizers and the runner. All system components are made of a highly concentrated, especially reinforced glass fiber or carbon fiber plastic material providing good low temperature impact strength. Based on the excellent system stability, the t'blade runner can take user weight loads of a maximum of 120 kg (264 lbs.) and can be used for hockey games up to an outside temperature of approximately.-25 degrees without any problems.The complete system contains a pair of :
white holders
grey stabilizers
white runners (M 13)
red clips
The skate blade system: The development of the t’ blade blade system took place as a result to create a blade system which is capable of eliminating a deficiency existing since than more 100 years in the sector of ice skate blades. With the market launch of the t’blade interchangeable runner technology, the market has for the first time in the history of ice skates a runner system which does not require a time-consuming and cost-intensive inaccurate sharpening process of the runner edges. The restoration of optimum gliding characteristics is achieved exclusively by the quick replacement of the t’blade interchangeable runners. The runner system has not only a wide range of outstanding features, but occupies a top position in the areas concerning gliding characteristics, maneuverability, high cornering speed, and braking deceleration. Furthermore, new standards have been set concerning the use of ice skate blades in areas like product stability, service life, system handling, product service and manufacturing quality. The interchangeable runners manufactured with the greatest precision have an absolutely constant rocker shape (contact area) and are only distinguished by the gliding surface length, the radius of hollow and the system size. A wide variety of versions allow the system user an accurate matching of the runner to suit the current state of the ice surface taking into account simultaneously its expectations concerning gliding characteristics during skating. The system matching is effected taking into account of the user weight and the ice surface temperature by modifying the gliding surface length and the radius of hollow. The skate blade system consists of three parts, the holder, the stabilizers and the runner. All system components are made of a highly concentrated, especially reinforced glass fiber or carbon fiber plastic material providing good low temperature impact strength. With a weight of < 189 grams, relative to the reference system size 272, the carbon runner is the lightest ice skate blade on the market . Based on the excellent system stability, the t'blade runner can take user weight loads of a maximum of 120 kg (264 lbs.) and can be used for hockey games up to an outside temperature of approximately -25 degrees C° without any problems. You can find a detailed description in the blade system area (runner) under "HOLDER, STABILIZERS and RUNNER".The holder:
available in 6 different colors
as well as in 6 metallized colors (refer to product variants)
The holder consists of high-strength impact-resistant fibrous plastic (glass or carbon fiber) which withstands temperatures of up to -25℃. Its ingenious bridge-like structure over the entire length from the front to the rear portion of the holder combined with the integrated cross ribs provide a high degree of rigidity with excellent torsional, longitudinal and transversal stability characteristics. The design related rigidity of the holder stabilizes the sole of the shoe in a sustainable manner and minimizes the axial bending forces in the central area of the ice skate shoe. A trapezoid shaped connecting element between the runner and the holder ensures a precise and tight seating of the runner into the holder enabling the transfer of acceleration and transverse cornering forces. To ensure a proper installation of the stabilizers, the inner side of the holder is provided with little cavities which are intended to install the locking washers of the screws to hold the stabilizers in place. If required, the holes around the perimeter of the sole can be used for securing the holder onto the sole of the ice skate. The fastening can then be realized by means of rivets or RMS screws.A recess located at the rear of the holder is provided for inserting the t’blade logo clip. Proper function and maximum rigidity of the holder are only ensured if all components are assembled. Advantages:
extreme stability of the holder thanks to the triangle of forces
maximum longitudinal and transversal stability characteristics
closed structure between the front and the rear area
visual differentiation thanks to the recesses and the bridge-like structure
sustained improvement of the rigidity of the sole of the ice skate shoe
The stabilizers:
available in 6 different colors
as well as in 6 metallized colors (refer to product variants)
The stabilizers are made of glass fiber plastic and have identical material properties as the holder. In addition, they are provided with a set of special light alloy screws and sockets to ensure play-free securing of the runner without damaging the plastic. There are two stabilizers on each t-blade system, one holding the nuts which are press-fitted to prevent them from falling out. The other one with the same number of special screws and locking washers to prevent them from being lost coincides perfectly with the nuts of the female stabilizer. The tightening torque of 1,2 Nm ensures a high level of stability and safety.Advantages:
rapid exchange of the runner
stable assembly of runner and holder
stiffening of transverse and longitudinal axis of the runner by means of the stabilizers
special light alloy screws and sockets to avoid damaging the plastic
special locking washers secured against losing
perfect form-closed positioning of the runner and the holder using cone clamping elements
extravagant design possibilities with a wide range of colors
The runner:
available per system size in 18 rocker shape variants
as well as in 2 different colors white and black
Detailed description of the available runner versions refer to product variants. The runner is an innovative very complex and technologically sophisticated composite product which constitutes almost the entire key technology of the t’blade runner system.The fabrication of the high-precision 1 mm thick metal band requires the use of the ultra-modern laser technology by means of complex production lines meeting the closest tolerances. The fracture resistant profiled running strip is made of a stainless steel or metal alloy which is injected into a low temperature resistant glass fiber or carbon fiber plastic .The highly compressed profiled running strip is manufactured by rolling and has an enormous edge hardness of approx. 55 HRC = 570 HV after an expensive and time-consuming fabrication process. The available maximum hardness achieves a useful life 4 times longer than traditional steel blades. Due to the very small metal mass (approx. 5.5g) of the running strip and a minimum plastic mass (approx. 45g), the t-blade composite runner is the lightest ice skate blade on the market worldwide. Due to the very small size of the profiled running strip, the runner has exceptional thermal properties which in conjunction with the highly polished running surface of the runner lead to an above-average improvement of the gliding characteristics up to 40 %. Due to its absolutely constant rocker shape, the runner available in many types allows a quick and perfect restoration of the usual optimum gliding characteristics. As soon as the running edges are worn or damaged, a rapid and simple replacement of the runner is required. Thus a time-consuming and cost-intensive inaccurate sharpening process of the runner edges is avoided. The rocker shape available in many versions is determined by three crucial factors: Gliding surface length, radius of hollow and system size (refer to product variants and rocker shape matching)Advantages:
extremely light
excellent gliding characteristics
good maneuverability
high cornering speed
small curve radii
fracture resistant
constant rocker shape geometry
running edges sharpening not required
above-average hardness of the running edges
useful life 4 times longer
rapid runner exchange
The logo clip:
available in 6 different colors
as well as in 6 metallized colors (refer to product variants)
The logo clip identifies the t’blade trademark (thermal blade) and refers to the outstanding thermal characteristics of the t'blade runner system.The central emblem shows the initial letter "t" which indicates the registered " t’blade brand name "as well as the blazing flame symbolizing the above-average temperature on the gliding surface. The impressively simple logo is made of not-reinforced plastic and fits exactly into the cavity intended for this purpose in the rear part of the holder. The logo clip can be replaced without any problem by inserting a screwdriver tip into the unlocking opening where the flame is located so that it can be dislodged easily. The logo-clip can be customized to suit the personal taste of the system user by means of a variety of colors. Advantages:
strong brand recognition
excellent visual appearance of the product
high-quality trademark
customized colors
easy interchangeability
Der Holder besteht aus einem kälteschlagzähen Kunststoff der bis zu einer Temperatur von maximal - 25 ° Celsius splitterbruchsicher ist. Seine effiziente brückenartige Konstruktion erstreckt sich durchgängige von der Holderfront bis zum Holderheck und führt im Verbund mit den integrierten Querrippen zu einem extrem steifen Holder mit hervorragenden Torsion, Längs- und Querstabilitätseigenschaften. Die konstruktionsbedingte Steifigkeit des Holders stabilisiert die Schlittschuhsohle nachhaltig und minimiert die axialen Biegekräfte im Zentralbereich des Schlittschuhstiefels. Mit einer genau definierten und geschlossenen Holder Sprengung unterstützt die Holderkonstruktion nachhaltig den optimalen Kniepunkt Vorhaltewinkel des Kufensystem Nutzers. Eine trapezartige Verbindung zwischen Runner und Holder gewährleistet einen spielfreien und passgenauen Sitz des Runners im Holder und ermöglicht dadurch die Übertragung von großen Beschleunigungs- und Kurvenquerkräften. Um eine planflächige und stabile Verbauung der Stabilisatoren zu ermöglichen, befinden sich an den Verschraubungspunkten im Bereich der Holder Innenseite, kleine Mulden, die dazu geeignet sind, die Sicherungsscheiben des Schrauben Stabilisators aufzunehmen. Eine fehlerhafte Montage der Stabilisatoren führt zwangsweise zu einem Stabilitätsverlust der Runner Verschraubung und beschleunigt die Zerstörung der Kunststoff Sicherungsscheiben. Die im Holder Sohlenrand umlaufend eingebrachten Befestigungslöcher können je nach Bedarf und Position zum befestigen des Holders an der Schlittschuhstiefelsohle benutzt werden. Die Befestigung kann mittels Nieten oder RMS Verschraubung erfolgen.Im Heckbereich des Holder befindet sich die Konturöffnung für das Einklinkbahre t-blade Logo-Clip Markenzeichen
Der Holder erreicht seine maximale Steifigkeit und Betriebssicherheit erst im Verbund aller Systemteile. Vorteile:Extreme Holder Stabilität durch Kräftedreieck-Konstruktion ++
Maximale Quer- und Längskraftstabilität ++ Geschlossene Holder
Konstruktion zwischen Front- und Heckbereich ++ Optische
Differenzierung durch Mehrloch- und Brückendesign ++ Nachhaltige
Verbesserung der Schlittschuhsohlensteifigkeit ++
Abbildungen beispielhaft - der Holder mit Systemlänge 248 mm hat 4 Aussparungen, ab Systemlänge 256 mm sind es 5 Aussparungen.
___________________________________________________________________
English
The holder forms the blade holder of the t'blade system and it is available in 2 standard colors (glass fiber plastic) as well as a carbon variant (carbon fiber plastic). The bridge-type construction, combined with the integrated lateral ribs, leads to an extremely stiff holder with good torsion, lateral and vertical stability characteristics. By means of the holes which are provided at the sole border, the holder can be fitted to the shoe via rivets or an RMS connection. Advantages-Holder made of fiber reinforced plastic -Cold impact resistant and chip fracture safe up to -25° C -Closed construction between front and heel area -Extreme stability by means of the triangle of forces construction - Improves stiffness of skate outsole-Maximum shear and longitudinal force stability System sizesStandard system: 248, 256, 264, 272, 280, 288, 300mm Carbon system: 248, 256, 264, 272, 280, 288, 300mm
The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants.
Advantages
Quick & Easy Runner Exchange
Fail-proof screwing parts
Stable connection between holder & runner
Use
Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side.
Der Holder besteht aus einem kälteschlagzähen Kunststoff der bis zu einer Temperatur von maximal - 25 ° Celsius splitterbruchsicher ist. Seine effiziente brückenartige Konstruktion erstreckt sich durchgängige von der Holderfront bis zum Holderheck und führt im Verbund mit den integrierten Querrippen zu einem extrem steifen Holder mit hervorragenden Torsion, Längs- und Querstabilitätseigenschaften. Die konstruktionsbedingte Steifigkeit des Holders stabilisiert die Schlittschuhsohle nachhaltig und minimiert die axialen Biegekräfte im Zentralbereich des Schlittschuhstiefels. Mit einer genau definierten und geschlossenen Holder Sprengung unterstützt die Holderkonstruktion nachhaltig den optimalen Kniepunkt Vorhaltewinkel des Kufensystem Nutzers. Eine trapezartige Verbindung zwischen Runner und Holder gewährleistet einen spielfreien und passgenauen Sitz des Runners im Holder und ermöglicht dadurch die Übertragung von großen Beschleunigungs- und Kurvenquerkräften. Um eine planflächige und stabile Verbauung der Stabilisatoren zu ermöglichen, befinden sich an den Verschraubungspunkten im Bereich der Holder Innenseite, kleine Mulden, die dazu geeignet sind, die Sicherungsscheiben des Schrauben Stabilisators aufzunehmen. Eine fehlerhafte Montage der Stabilisatoren führt zwangsweise zu einem Stabilitätsverlust der Runner Verschraubung und beschleunigt die Zerstörung der Kunststoff Sicherungsscheiben. Die im Holder Sohlenrand umlaufend eingebrachten Befestigungslöcher können je nach Bedarf und Position zum befestigen des Holders an der Schlittschuhstiefelsohle benutzt werden. Die Befestigung kann mittels Nieten oder RMS Verschraubung erfolgen.Im Heckbereich des Holder befindet sich die Konturöffnung für das Einklinkbahre t-blade Logo-Clip Markenzeichen
Der Holder erreicht seine maximale Steifigkeit und Betriebssicherheit erst im Verbund aller Systemteile. Vorteile:Extreme Holder Stabilität durch Kräftedreieck-Konstruktion ++
Maximale Quer- und Längskraftstabilität ++ Geschlossene Holder
Konstruktion zwischen Front- und Heckbereich ++ Optische
Differenzierung durch Mehrloch- und Brückendesign ++ Nachhaltige
Verbesserung der Schlittschuhsohlensteifigkeit ++
Abbildungen beispielhaft - der Holder mit Systemlänge 248 mm hat 4 Aussparungen, ab Systemlänge 256 mm sind es 5 Aussparungen.
___________________________________________________________________
English
The holder forms the blade holder of the t'blade system and it is available in 2 standard colors (glass fiber plastic) as well as a carbon variant (carbon fiber plastic). The bridge-type construction, combined with the integrated lateral ribs, leads to an extremely stiff holder with good torsion, lateral and vertical stability characteristics. By means of the holes which are provided at the sole border, the holder can be fitted to the shoe via rivets or an RMS connection. Advantages-Holder made of fiber reinforced plastic -Cold impact resistant and chip fracture safe up to -25° C -Closed construction between front and heel area -Extreme stability by means of the triangle of forces construction - Improves stiffness of skate outsole-Maximum shear and longitudinal force stability System sizesStandard system: 248, 256, 264, 272, 280, 288, 300mm Carbon system: 248, 256, 264, 272, 280, 288, 300mm
The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants.
Advantages
Quick & Easy Runner Exchange
Fail-proof screwing parts
Stable connection between holder & runner
Use
Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side.
The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants.
Advantages
Quick & Easy Runner Exchange
Fail-proof screwing parts
Stable connection between holder & runner
Use
Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side.
Unser neuestes Produkt in der t´blade Familie, der Nightlight Holder, EXKLUSIV und EINZIGARTIG!!!
Einfach die Holder in der Sonne oder im Licht aufladen und ab aufs Eis.
Der Holder besteht aus einem kälteschlagzähen hochfesten Glasfaser- Kunststoff
der bis zu einer Temperatur von maximal – 25 ° Celsius splitterbruchsicher ist. Seine effiziente brückenartige Konstruktion erstreckt sich durchgängige von der Holderfront bis zum Holderheck und führt im Verbund mit den integrierten Querrippen zu einem extrem steifen Holder mit hervorragenden Torsion, Längs- und Querstabilitätseigen-schaften. Die konstruktionsbedingte Steifigkeit des Holders stabilisiert die Schlittschuhsohle nachhaltig und minimiert die axialen Biegekräfte im Zentralbereich des Schlittschuhstiefels. Mit einer genau definierten und geschlossenen Holder Sprengung unterstützt die Holderkonstruktion nachhaltig den optimalen Kniepunkt Vorhaltewinkel des Kufensystem Nutzers. Eine trapezartige Verbindung zwischen Runner und Holder gewährleistet einen spielfreien und passgenauen Sitz des Runners im Holder und ermöglicht dadurch die Übertragung von großen Beschleunigungs- und Kurvenquerkräften. Um eine planflächige und stabile Verbauung der Stabilisatoren zu ermöglichen, befinden sich an den Verschraubungspunkten im Bereich der Holder Innenseite, kleine Mulden, die dazu geeignet sind, die Sicherungsscheiben des Schrauben Stabilisators aufzunehmen. Eine fehlerhafte Montage der Stabilisatoren führt zwangsweise zu einem Stabilitätsverlust der Runner Verschraubung und beschleunigt die Zerstörung der Kunststoff Sicherungsscheiben. Die im Holder Sohlenrand umlaufend eingebrachten Befestigungslöcher können je nach Bedarf und Position zum befestigen des Holders an der Schlittschuhstiefelsohle benutzt werden. Die Befestigung kann mittels Nieten oder RMS Verschraubung erfolgen. Im Heckbereich des Holder befindet sich die Konturöffnung für das Einklinkbahre t’ blade Logo-Clip Markenzeichen
Der Holder erreicht seine maximale Steifigkeit und Betriebssicherheit erst im Verbund aller Systemteile. Vorteile: Extreme Holder Stabilität durch Kräftedreieck-Konstruktion ++
Maximale Quer- und Längskraftstabilität ++ Geschlossene Holder
Konstruktion zwischen Front- und Heckbereich ++ Optische
Differenzierung durch Mehrloch- und Brückendesign ++ Nachhaltige
Verbesserung der Schlittschuhsohlensteifigkeit ++
Abbildungen beispielhaft - der Holder mit Systemlänge 248 mm hat 4 Aussparungen, ab Systemlänge 256 mm sind es 5 Aussparungen.
___________________________________________________________________
English
The holder forms the blade holder of the t'blade system and it is available in 2 standard colors (glass fiber plastic) as well as a carbonvariant (carbon fiber plastic). The bridge-type construction, combined with the integrated lateral ribs, leads to an extremely stiff holderwith good torsion, lateral and vertical stability characteristics. By means of the holes which are provided at the sole border, the holder can be fitted to the shoe via rivets or an RMS connection. Advantages-Holder made of fiber reinforced plastic -Cold impact resistant and chip fracture safe up to -25° C -Closed construction between front and heel area -Extreme stability by means of the triangle of forces construction - Improves stiffness of skate outsole-Maximum shear and longitudinal force stability System sizesStandard system: 248, 256, 264, 272, 280, 288, 300mm Carbon system: 248, 256, 264, 272, 280, 288, 300mm
The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants.
Advantages
Quick & Easy Runner Exchange
Fail-proof screwing parts
Stable connection between holder & runner
Use
Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side.
The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants.
Advantages
Quick & Easy Runner Exchange
Fail-proof screwing parts
Stable connection between holder & runner
Use
Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side.
Alle Größen lieferbar ab Mitte August
Der Holder besteht aus einem kälteschlagzähen Kunststoff der bis zu einer Temperatur von maximal - 25 ° Celsius splitterbruchsicher ist. Seine effiziente brückenartige Konstruktion erstreckt sich durchgängige von der Holderfront bis zum Holderheck und führt im Verbund mit den integrierten Querrippen zu einem extrem steifen Holder mit hervorragenden Torsion, Längs- und Querstabilitätseigenschaften. Die konstruktionsbedingte Steifigkeit des Holders stabilisiert die Schlittschuhsohle nachhaltig und minimiert die axialen Biegekräfte im Zentralbereich des Schlittschuhstiefels. Mit einer genau definierten und geschlossenen Holder Sprengung unterstützt die Holderkonstruktion nachhaltig den optimalen Kniepunkt Vorhaltewinkel des Kufensystem Nutzers. Eine trapezartige Verbindung zwischen Runner und Holder gewährleistet einen spielfreien und passgenauen Sitz des Runners im Holder und ermöglicht dadurch die Übertragung von großen Beschleunigungs- und Kurvenquerkräften. Um eine planflächige und stabile Verbauung der Stabilisatoren zu ermöglichen, befinden sich an den Verschraubungspunkten im Bereich der Holder Innenseite, kleine Mulden, die dazu geeignet sind, die Sicherungsscheiben des Schrauben Stabilisators aufzunehmen. Eine fehlerhafte Montage der Stabilisatoren führt zwangsweise zu einem Stabilitätsverlust der Runner Verschraubung und beschleunigt die Zerstörung der Kunststoff Sicherungsscheiben. Die im Holder Sohlenrand umlaufend eingebrachten Befestigungslöcher können je nach Bedarf und Position zum befestigen des Holders an der Schlittschuhstiefelsohle benutzt werden. Die Befestigung kann mittels Nieten oder RMS Verschraubung erfolgen.Im Heckbereich des Holder befindet sich die Konturöffnung für das Einklinkbahre t-blade Logo-Clip Markenzeichen
Der Holder erreicht seine maximale Steifigkeit und Betriebssicherheit erst im Verbund aller Systemteile. Vorteile:Extreme Holder Stabilität durch Kräftedreieck-Konstruktion ++
Maximale Quer- und Längskraftstabilität ++ Geschlossene Holder
Konstruktion zwischen Front- und Heckbereich ++ Optische
Differenzierung durch Mehrloch- und Brückendesign ++ Nachhaltige
Verbesserung der Schlittschuhsohlensteifigkeit ++
Abbildungen beispielhaft - der Holder mit Systemlänge 248 mm hat 4 Aussparungen, ab Systemlänge 256 mm sind es 5 Aussparungen.
___________________________________________________________________
English
The holder forms the blade holder of the t'blade system and it is available in 2 standard colors (glass fiber plastic) as well as a carbon variant (carbon fiber plastic). The bridge-type construction, combined with the integrated lateral ribs, leads to an extremely stiff holder with good torsion, lateral and vertical stability characteristics. By means of the holes which are provided at the sole border, the holder can be fitted to the shoe via rivets or an RMS connection. Advantages-Holder made of fiber reinforced plastic -Cold impact resistant and chip fracture safe up to -25° C -Closed construction between front and heel area -Extreme stability by means of the triangle of forces construction - Improves stiffness of skate outsole-Maximum shear and longitudinal force stability System sizesStandard system: 248, 256, 264, 272, 280, 288, 300mm
Der Holder besteht aus einem kälteschlagzähen Kunststoff der bis zu einer Temperatur von maximal - 25 ° Celsius splitterbruchsicher ist. Seine effiziente brückenartige Konstruktion erstreckt sich durchgängige von der Holderfront bis zum Holderheck und führt im Verbund mit den integrierten Querrippen zu einem extrem steifen Holder mit hervorragenden Torsion, Längs- und Querstabilitätseigenschaften. Die konstruktionsbedingte Steifigkeit des Holders stabilisiert die Schlittschuhsohle nachhaltig und minimiert die axialen Biegekräfte im Zentralbereich des Schlittschuhstiefels. Mit einer genau definierten und geschlossenen Holder Sprengung unterstützt die Holderkonstruktion nachhaltig den optimalen Kniepunkt Vorhaltewinkel des Kufensystem Nutzers. Eine trapezartige Verbindung zwischen Runner und Holder gewährleistet einen spielfreien und passgenauen Sitz des Runners im Holder und ermöglicht dadurch die Übertragung von großen Beschleunigungs- und Kurvenquerkräften. Um eine planflächige und stabile Verbauung der Stabilisatoren zu ermöglichen, befinden sich an den Verschraubungspunkten im Bereich der Holder Innenseite, kleine Mulden, die dazu geeignet sind, die Sicherungsscheiben des Schrauben Stabilisators aufzunehmen. Eine fehlerhafte Montage der Stabilisatoren führt zwangsweise zu einem Stabilitätsverlust der Runner Verschraubung und beschleunigt die Zerstörung der Kunststoff Sicherungsscheiben. Die im Holder Sohlenrand umlaufend eingebrachten Befestigungslöcher können je nach Bedarf und Position zum befestigen des Holders an der Schlittschuhstiefelsohle benutzt werden. Die Befestigung kann mittels Nieten oder RMS Verschraubung erfolgen.Im Heckbereich des Holder befindet sich die Konturöffnung für das Einklinkbahre t-blade Logo-Clip Markenzeichen
Der Holder erreicht seine maximale Steifigkeit und Betriebssicherheit erst im Verbund aller Systemteile. Vorteile:Extreme Holder Stabilität durch Kräftedreieck-Konstruktion ++
Maximale Quer- und Längskraftstabilität ++ Geschlossene Holder
Konstruktion zwischen Front- und Heckbereich ++ Optische
Differenzierung durch Mehrloch- und Brückendesign ++ Nachhaltige
Verbesserung der Schlittschuhsohlensteifigkeit ++
Abbildungen beispielhaft - der Holder mit Systemlänge 248 mm hat 4 Aussparungen, ab Systemlänge 256 mm sind es 5 Aussparungen.
___________________________________________________________________
English
The holder forms the blade holder of the t'blade system and it is available in 2 standard colors (glass fiber plastic) as well as a carbon variant (carbon fiber plastic). The bridge-type construction, combined with the integrated lateral ribs, leads to an extremely stiff holder with good torsion, lateral and vertical stability characteristics. By means of the holes which are provided at the sole border, the holder can be fitted to the shoe via rivets or an RMS connection. Advantages-Holder made of fiber reinforced plastic -Cold impact resistant and chip fracture safe up to -25° C -Closed construction between front and heel area -Extreme stability by means of the triangle of forces construction - Improves stiffness of skate outsole-Maximum shear and longitudinal force stability System sizesStandard system: 248, 256, 264, 272, 280, 288, 300mm Carbon system: 248, 256, 264, 272, 280, 288, 300mm
Nur noch wenige Größen auf Lager,
*** Dies sind Sonder-Posten und können nicht nachbestellt werden.***
Holder pearl-gold.
Der Holder besteht aus einem kälteschlagzähen Kunststoff der bis zu einer Temperatur von maximal - 25 ° Celsius
splitterbruchsicher ist. Seine effiziente brückenartige Konstruktion erstreckt sich durchgängige von der Holderfront bis zum Holderheck und führt im Verbund mit den integrierten Querrippen zu einem extrem steifen Holder mit hervorragenden Torsion, Längs- und Querstabilitätseigenschaften. Die konstruktionsbedingte Steifigkeit des Holders stabilisiert die Schlittschuhsohle nachhaltig und minimiert die axialen Biegekräfte im Zentralbereich des Schlittschuhstiefels. Mit einer genau definierten und geschlossenen Holder Sprengung unterstützt die Holderkonstruktion nachhaltig den optimalen Kniepunkt Vorhaltewinkel des Kufensystem Nutzers. Eine trapezartige Verbindung zwischen Runner und Holder gewährleistet einen spielfreien und passgenauen Sitz des Runners im Holder und ermöglicht dadurch die Übertragung von großen Beschleunigungs- und Kurvenquerkräften. Um eine planflächige und stabile Verbauung der Stabilisatoren zu ermöglichen, befinden sich an den Verschraubungspunkten im Bereich der Holder Innenseite, kleine Mulden, die dazu geeignet sind, die Sicherungsscheiben des Schrauben Stabilisators aufzunehmen. Eine fehlerhafte Montage der Stabilisatoren führt zwangsweise zu einem Stabilitätsverlust der Runner Verschraubung und beschleunigt die Zerstörung der Kunststoff Sicherungsscheiben. Die im Holder Sohlenrand umlaufend eingebrachten Befestigungslöcher können je nach Bedarf und Position zum befestigen des Holders an der Schlittschuhstiefelsohle benutzt werden. Die Befestigung kann mittels Nieten oder RMS Verschraubung erfolgen.Im Heckbereich des Holder befindet sich die Konturöffnung für das Einklinkbahre t-blade Logo-Clip Markenzeichen
Der Holder erreicht seine maximale Steifigkeit und Betriebssicherheit erst im Verbund aller Systemteile. Vorteile:Extreme Holder Stabilität durch Kräftedreieck-Konstruktion ++
Maximale Quer- und Längskraftstabilität ++ Geschlossene Holder
Konstruktion zwischen Front- und Heckbereich ++ Optische
Differenzierung durch Mehrloch- und Brückendesign ++ Nachhaltige
Verbesserung der Schlittschuhsohlensteifigkeit ++
Abbildungen beispielhaft - der Holder mit Systemlänge 248 mm hat 4 Aussparungen, ab Systemlänge 256 mm sind es 5 Aussparungen.
___________________________________________________________________
English
The holder forms the blade holder of the t'blade system and it is available in 2 standard colors (glass fiber plastic) as well as a carbon variant (carbon fiber plastic). The bridge-type construction, combined with the integrated lateral ribs, leads to an extremely stiff holder with good torsion, lateral and vertical stability characteristics. By means of the holes which are provided at the sole border, the holder can be fitted to the shoe via rivets or an RMS connection. Advantages-Holder made of fiber reinforced plastic -Cold impact resistant and chip fracture safe up to -25° C -Closed construction between front and heel area -Extreme stability by means of the triangle of forces construction - Improves stiffness of skate outsole-Maximum shear and longitudinal force stability System sizesStandard system: 256, 272, 280, 300 mm
The stabilizer is made of fiberglass reinforced plastic and serves to affix the runner to the holder. It consists of a screw and nut side, which are connected using a system key. The stabilizer is available in seven standard colors and six metallic variants.
Advantages
Quick & Easy Runner Exchange
Fail-proof screwing parts
Stable connection between holder & runner
Use
Loosen all the screws using the key. Then, press the key with the screws to detach the against groove side of the stabilizer. Take off both sides (nut and screw side) of the stabilizer. After swapping out the runner, push the groove side into the holder first. Then attach the screw side of the stabilizer and fasten the screws. Please note that for an easier mounting and dismounting, the screw side of the stabilizer should always be on the inner shoe side.
Der Logo Clip: Erhältlich in 3 Standard-Kunststofffarben sowie 6 Metallic-Farben (siehe Produkt-Varianten)Der Logo Clip thematisiert mit seiner Ausgestaltung den Markennamen t-blade (Thermo- Messer) und verweist in seinem Logo auf die exzellenten thermischen Eigenschaften des Kufensystems.
Das zentrale Emblem t zeigt den Anfangsbuchstaben des weltweit geschützten Markennamen t-blade sowie eine lodernde Flamme, die symbolisch auf die Erzeugung einer überdurchschnittlich hohen Gleitflächen Temperatur hinweist.
Das bestechend Logo besteht aus Kunststoff und rastet passgenau in die Konturform am Holder-Heck ein. Durch seitliches einschieben eines kleinen Schraubendrehers in die Flamme, lässt sich der Logo-Clip aus der Verrastung aushebeln und kann problemlos ausgetauscht werden.
Über eine Vielzahl von Farben kann der Logo-Clip dem persönlichen Geschmack des System-Nutzers angepasst werden.Vorteile:Hoher Marken Erkennungswert ++ exzellente Produktoptik ++ Hochwertige Markenbezeichnung ++ individuelle Farbgestaltung ++ leichte Austauschbarkeit.
English
ClipCharacteristicsThe t'blade clip, which is attached to the holder, is available in colors which match with the one of the stabilizer. It is made of non-reinforced plastic and is available in 2 standard colors as well as 6 metallic variants. The logo clip has a pure design function.