t-blade Systemschlüssel - Metall

€9.99*

Content: 1 Stück

Available, delivery time: 2-5 days

Stück
Product number: 100068-07-203-0100-0000
Product information "t-blade Systemschlüssel - Metall"

Der Systemschlüssel dient beim Wechseln des Ersatzmessers zum Lösen bzw. Anziehen der Stabilisator-Schrauben. Er besteht aus einem Leichtmetall mit eloxierter Oberfläche und besitzt eine verschleißarme Verzahnung.

Systemschlüssel - Metall wir nur benötigt bei Metallverschraubung.

 

English

System key

Characteristics
The system key is needed for loosening or tightening the stabilizer screws when exchanging the runner. It is made from a light alloy
with a red anodized surface and has a wear-resistant keying. For frequent runner exchange, an appropriate bit, made of hardened steel,
is available and this can be used in cordless screwdrivers.

11 of 11 reviews

4.68 out of 5 stars


82%

9%

9%

0%

0%


Leave a review!

Share your experiences with other customers.


2 April 2023 23:11

Passt nicht auf meine Schrauben (aus Metall)

Optisch und technisch einwandfreies Produkt. Jedoch von mir falsch bestellt, da angegeben war, dass man den Schlüssel für die Metallverschraubungen bräuchte. Jedoch funktionierte es bei mir nicht und ich musste mir mit einem Torx Schraubenschlüssel helfen. Das hat dann einwandfrei funktioniert. Ich habe anscheinend die Ersatzschrauben (habe gebrauchte Schuhe gekauft) Tip an den Verkäufer: ein Bild mit den kompatiblen Schrauben wäre eindeutiger, vor allem wenn es verschiedene mögliche Metallverschraubungen gibt.

7 February 2022 17:12

Super verarbeitet

Sieht super aus und ist sauber verarbeitet. Ohne geht es nicht.

3 February 2022 11:53

Top Werkzeug

Hochwertig und sauber verarbeitet.

13 March 2020 07:43

Systemschlüssel

Sehr gut verarbeitet und macht das was es soll.

28 January 2020 16:44

Alles ok

Super verarbeitet er ist sein Geld wert!

11 January 2020 09:38

Ein muss

Sehr gut verarbeitet! Funktioniet einwandfrei,habe ihn immer beim laufen dabei

4 October 2016 23:26

Zweckmäßig

Praktisch, tut eben was er soll. Nutzt sich auch irgenwann ab aber versagt nicht und ist immer dabei.

28 September 2016 20:11

Der Schlüssel ist ein muss, wenn man sich die Metallschrauben bestellt hat, die die Runner halten

Immer wieder

2 January 2016 18:28

Ein must have

Der Schlüssel ist ein muss, wenn man sich die Metallschrauben bestellt hat, die die Runner halten.

16 March 2015 11:01

Systemschlüssel

Funktioniert gut

Accessory Items

%
t-blade complete system 248
The skate blade system consists of three parts, the holder, the stabilizers and the runner. All system components are made of a highly concentrated, especially reinforced glass fiber or carbon fiber plastic material providing good low temperature impact strength. Based on the excellent system stability, the t'blade runner can take user weight loads of a maximum of 120 kg (264 lbs.) and can be used for hockey games up to an outside temperature of approximately.-25 degrees without any problems.The complete system contains a pair of : white holders grey stabilizers white runners (M 13) red clips According to the illustrations as examples – on the basis of a system length of 248 mm, the holder has 4 recesses, the stabilizers, the runner  and 5 screw holes. The skate blade system: The development of the t’ blade blade system took place as a result to create a blade system which is capable of eliminating a deficiency existing since than more 100 years in the sector of ice skate blades. With the market launch of the t’blade interchangeable runner technology, the market has for the first time in the history of ice skates a runner system which does not require a time-consuming and cost-intensive inaccurate sharpening process of the runner edges. The restoration of optimum gliding characteristics is achieved exclusively by the quick replacement of the t’blade interchangeable runners. The runner system has not only a wide range of outstanding features, but occupies a top position in the areas concerning gliding characteristics, maneuverability, high cornering speed, and braking deceleration. Furthermore, new standards have been set concerning the use of ice skate blades in areas like product stability, service life, system handling, product service and manufacturing quality. The interchangeable runners manufactured with the greatest precision have an absolutely constant rocker shape (contact area) and are only distinguished by the gliding surface length, the radius of hollow and the system size. A wide variety of versions allow the system user an accurate matching of the runner to suit the current state of the ice surface taking into account simultaneously its expectations concerning gliding characteristics during skating. The system matching is effected taking into account of the user weight and the ice surface temperature by modifying the gliding surface length and the radius of hollow. The skate blade system consists of three parts, the holder, the stabilizers and the runner. All system components are made of a highly concentrated, especially reinforced glass fiber or carbon fiber plastic material providing good low temperature impact strength. With a weight of < 189 grams, relative to the reference system size 272, the carbon runner is the lightest ice skate blade on the market . Based on the excellent system stability, the t'blade runner can take user weight loads of a maximum of 120 kg (264 lbs.) and can be used for hockey games up to an outside temperature of approximately -25 degrees C° without any problems. You can find a detailed description in the blade system area (runner) under  "HOLDER, STABILIZERS and RUNNER".The holder:         available in 6 different colors as well as in 6 metallized colors (refer to product variants) The holder consists of high-strength impact-resistant fibrous plastic (glass or carbon fiber) which withstands temperatures of up to -25℃.                                                                                     Its ingenious bridge-like structure over the entire length from the front to the rear portion of the holder combined with the integrated cross ribs provide a high degree of rigidity with excellent torsional, longitudinal and transversal stability characteristics. The design related rigidity of the holder stabilizes the sole of the shoe in a sustainable manner and minimizes the axial bending forces in the central area of the ice skate shoe. A trapezoid shaped connecting element between the runner and the holder ensures a precise and tight seating of the runner into the holder enabling the transfer of acceleration and transverse cornering forces. To ensure a proper installation of the stabilizers, the inner side of the holder is provided with little cavities which are intended to install the locking washers of the screws to hold the stabilizers in place. If required, the holes around the perimeter of the sole can be used for securing the holder onto the sole of the ice skate. The fastening can then be realized by means of rivets or RMS screws.A recess located at the rear of the holder is provided for inserting the t’blade logo clip. Proper function and maximum rigidity of the holder are only ensured if all components are assembled. Advantages: extreme stability of the holder thanks to the triangle of forces maximum longitudinal and transversal stability characteristics closed structure between the front and the rear area visual differentiation thanks to the recesses and the bridge-like structure sustained improvement of the rigidity of the sole of the ice skate shoe The stabilizers:         available in 6 different colors as well as in 6 metallized colors (refer to product variants) The stabilizers are made of glass fiber plastic and have identical material properties as the holder. In addition, they are provided with a set of special light alloy screws and sockets to ensure play-free securing of the runner without damaging the plastic. There are two stabilizers on each t-blade system, one holding the nuts which are press-fitted to prevent them from falling out. The other one with the same number of special screws and locking washers to prevent them from being lost coincides perfectly with the nuts of the female stabilizer. The tightening torque of 1,2 Nm ensures a high level of stability and safety.Advantages: rapid exchange of the runner stable assembly of runner and holder stiffening of transverse and longitudinal axis of the runner by means of the stabilizers special light alloy screws and sockets to avoid damaging the plastic special locking washers secured against losing perfect form-closed positioning of the runner and the holder using cone clamping elements extravagant design possibilities with a wide range of colors The runner:         available per system size in 18 rocker shape variants                 as well as in 2 different colors white and black          Detailed description of the available runner versions refer to product variants. The runner is an innovative very complex and technologically sophisticated composite product which constitutes almost the entire key technology of the t’blade runner system.The fabrication of the high-precision 1 mm thick metal band requires the use of the ultra-modern laser technology by means of complex production lines meeting the closest tolerances. The fracture resistant profiled running strip is made of a stainless steel or metal alloy which is injected into a low temperature resistant glass fiber or carbon fiber plastic .The highly compressed profiled running strip is manufactured by rolling and has an enormous edge hardness of approx. 55 HRC = 570 HV after an expensive and time-consuming fabrication process. The available maximum hardness achieves a useful life 4 times longer than traditional steel blades. Due to the very small metal mass (approx. 5.5g) of the running strip and a minimum plastic mass (approx. 45g), the t-blade composite runner is the lightest ice skate blade on the market worldwide. Due to the very small size of the profiled running strip, the runner has exceptional thermal properties which in conjunction with the highly polished running surface of the runner lead to an above-average improvement of the gliding characteristics up to 40 %. Due to its absolutely constant rocker shape, the runner available in many types allows a quick and perfect restoration of the usual optimum gliding characteristics. As soon as the running edges are worn or damaged, a rapid and simple replacement of the runner is required. Thus a time-consuming and cost-intensive inaccurate sharpening process of the runner edges is avoided. The rocker shape available in many versions is determined by three crucial factors: Gliding surface length, radius of hollow and system size (refer to product variants and rocker shape matching)Advantages: extremely light excellent gliding characteristics good maneuverability high cornering speed small curve radii fracture resistant constant rocker shape geometry running edges sharpening not required above-average hardness of the running edges useful life 4 times longer rapid runner exchange The logo clip:     available in 6 different colors                                as well as in 6 metallized colors (refer to product variants)          The logo clip identifies the t’blade trademark (thermal blade) and refers to the outstanding thermal characteristics of the t'blade runner system.The central emblem shows the initial letter "t" which indicates the registered " t’blade brand name "as well as the blazing flame symbolizing the above-average temperature on the gliding surface. The impressively simple logo is made of not-reinforced plastic and fits exactly into the cavity intended for this purpose in the rear part of the holder. The logo clip can be replaced without any problem by inserting a screwdriver tip into the unlocking opening where the flame is located so that it can be dislodged easily. The logo-clip can be customized to suit the personal taste of the system user by means of a variety of colors. Advantages: strong brand recognition excellent visual appearance of the product high-quality trademark customized colors easy interchangeability

€79.99* €100.95* (20.76% saved)
t-blade clip metallic-blau
Der Logo Clip:                      Erhältlich in 3 Standard-Kunststofffarben sowie                                                 6  Metallic-Farben  (siehe Produkt-Varianten)Der Logo Clip thematisiert mit seiner Ausgestaltung den Markennamen t-blade  (Thermo- Messer) und verweist in seinem Logo auf die exzellenten thermischen Eigenschaften des Kufensystems.    Das zentrale Emblem t zeigt den Anfangsbuchstaben des weltweit geschützten Markennamen t-blade sowie eine lodernde Flamme, die symbolisch auf die Erzeugung einer überdurchschnittlich hohen Gleitflächen Temperatur  hinweist. Das bestechend Logo besteht aus Kunststoff und rastet passgenau in die Konturform am Holder-Heck ein. Durch seitliches einschieben eines kleinen Schraubendrehers in die Flamme, lässt sich der Logo-Clip aus der Verrastung aushebeln und kann problemlos ausgetauscht werden. Über eine Vielzahl von Farben kann der Logo-Clip dem persönlichen Geschmack des System-Nutzers angepasst werden.Vorteile:Hoher Marken Erkennungswert  ++  exzellente Produktoptik  ++  Hochwertige Markenbezeichnung  ++  individuelle Farbgestaltung  ++  leichte Austauschbarkeit.      English ClipCharacteristicsThe t'blade clip, which is attached to the holder, is available in colors which match with the one of the stabilizer. It is made of non-reinforced plastic and is available in 2 standard colors as well as 6 metallic variants. The logo clip has a pure design function.  

€7.49*